Λογαριασμός Επικοινωνία
Το καλάθι σας
Αποστολή με DPD & FedEx
Βοήθεια; Ρωτήστε το AI

Σύστημα διαχείρισης μπαταρίας VICTRON ENERGY Smart BMS 12/200 (BMS210055000)

Σύστημα διαχείρισης μπαταρίας VICTRON ENERGY Smart BMS 12/200 (BMS210055000)
Σύστημα διαχείρισης μπαταρίας VICTRON ENERGY Smart BMS 12/200 (BMS210055000)
203,94 €
PDF
PDF

Αποστολή & επιστροφές

Εκτιμώμενη παράδοση Δευτέρα, 30 Νοεμβρίου
Θα ενημερώνεστε μέσω του αναλυτικού μας συστήματος παρακολούθησης
Τρόποι πληρωμής
Τραπεζική κάρταVisaMastercardPayPalApple PayGoogle PayΤραπεζική κατάθεση

Κάντε μια ερώτηση – ο βοηθός AI απαντά αμέσως.

Περιγραφή

The Smart BMS 12/200 for Victron LiFePO4 batteries is designed for 12V systems with a 12V alternator and combines a current limiter, battery combiner and battery monitor.

  • Alternator and battery protection
  • Load/battery charger output/input
  • Remote on/off

The Smart BMS 12/200 from Victron Energy (MPN BMS210055000) for intelligent Victron lithium iron phosphate batteries (LiFePO4) is specifically designed for 12V systems with a 12V alternator. It combines a current limiter, battery combiner and battery monitor in a robust and compact solution. The Smart BMS 12/200 monitors and protects each individual battery cell within the battery (or battery bank) and disconnects the alternator, charging sources or DC loads in case of low/high battery voltage or overtemperature.

The dedicated alternator connection provides current limiting and one-way traffic from the alternator to the battery, so that alternators of any size (and starter batteries) can be safely connected to the Smart Lithium battery and the starter battery is protected from excessive discharge. The BMS is equipped with Bluetooth for monitoring and configuration, a remote on/off connector to turn off the BMS (and the system) via a switch and a pre-alarm contact to give a warning signal before the BMS disconnects the battery from the system.

Features

  • Starter battery protection
  • Load/battery charger output/input (power supply socket SYSTEM+)
  • Lithium-ion battery protection
  • Load disconnect, pre-alarm and charge disconnect output
  • Remote on/off, also configurable as system on/off

The input current is electronically limited to approx. 90% of the fuse rating. A 100A fuse, for example, therefore limits the input current to approx. 90A. Choosing the correct fuse helps protect the LFP battery from excessive charge current (important in case of a low capacity LFP battery). In addition, the alternator is protected from overload in case of a high capacity LFP battery bank (most 12V alternators overheat and fail if operated at maximum output for more than 5 minutes).

Via this power supply socket, the LFP battery can be either charged or discharged (i.e. via a charger or inverter) with a max. continuous current of 200A in both directions. It can also be used as a load output, so that DC loads can be connected directly to this connection. The connection is short-circuit proof with a peak discharge current of 400A. The Smart BMS ensures that discharging of the battery is switched off in case of imminent cell undervoltage. It allows charging via this connection, but no charging algorithm can be applied internally.

Excessive input voltages and transients are regulated down to a safe level. The Smart BMS stops charging in case of cell overvoltage or overtemperature. It has three outputs:

  • Load disconnect output: The load output can be used to control the remote on/off of a battery protect, an inverter, a DC/DC converter or other loads.
  • Pre-alarm output: The pre-alarm output can be used as a warning when the battery voltage is low and it will trigger shortly before deactivation of the load disconnect output due to cell undervoltage. It can be used to control a relay, LED or buzzer. It can be configured as a continuous or intermittent signal.
  • Charge disconnect output: The charger output is normally high and becomes free floating in case of imminent cell overvoltage or overtemperature. The charger output can be used to control the remote on/off of a charger, a Cyrix-Li charge relay or a Cyrix-Li-Ct battery combiner.

A non-inverting or inverting on/off cable may be required.

The remote on/off controls charging via the alternator, while the BMS functionality remains active regardless of the remote on/off state. The remote can also be used as a system on/off switch. This can be configured with VictronConnect.

Χαρακτηριστικά

Χαρακτηριστικά
EAN
8719076052883
MPN
BMS210055000
Βάρος
2 kg
Εύρος θερμοκρασίας λειτουργίας
-40°C - +60°C
Κατηγορία
Αξεσουάρ ηλιακών μπαταριών
Κωδικός διεθνούς προστασίας (IP)
IP65
Μάρκα
VICTRON ENERGY
Μέγεθος
65 x 120 x 340 mm
Μέγιστο ρεύμα
200 A
Μοντέλο
BMS210055000
Ρεύμα φόρτισης
100 A (alternator connection, with 125 A fuse)
Τάση
12 V
Τάση μπαταρίας
12 V
Τύπος προϊόντος
Battery Management System (BMS)
Ιστορικό τιμών τους τελευταίους 6 μήνες
Σύστημα διαχείρισης μπαταρίας VICTRON ENERGY Smart BMS 12/200 (BMS210055000)
Τρέχουσα
203,94 €
Χαμηλότερη 7 ημ.
203,94 €
Υψηλότερη 7 ημ.
203,94 €
Μεταβολή 24 ωρών
0,00 €   0%
Μεταβολή 7 ημ.
—   
Μεταβολή 30 ημ.
—   

Γράψτε μια αξιολόγηση

Βαθμολογία *
Το όνομά σας θα εμφανίζεται δημόσια – μπορείτε να χρησιμοποιήσετε ψευδώνυμο. Προσκαλούμε τους αγοραστές να γράφουν αξιολογήσεις. Τις ελέγχουμε πριν από τη δημοσίευση και δημοσιεύουμε επίσης τις αρνητικές.

Περισσότερα προϊόντα VICTRON ENERGY σε αυτή την κατηγορία

10

Δημοφιλή προϊόντα σε αυτή την κατηγορία

4
Πωλητής: UAB KUR LT · Gariūnų g. 57-14, LT-02300 Βίλνιους, Λιθουανία · Κωδικός εταιρείας 303192950 · ΑΦΜ/ΦΠΑ ΕΕ LT100008198612 · Αποστολή από την ΕΕ (Λιθουανία)
WhatsApp
Messenger
Γεια σας, είμαι ο βοηθός AI του DistriNode. Μπορώ να σας βοηθήσω να βρείτε προϊόντα, να συγκρίνετε επιλογές, να δημιουργήσετε PDF προσφορών ή να ανοίξετε αιτήματα υποστήριξης.
Όλες οι κατηγορίες